GSI Forum: NUSTAR PRESPEC » Position calculations on start/stop scintillators

Home » NUSTAR » NUSTAR PRESPEC » Position calculations on start/stop scintillators

Show: Today's Messages :: Polls :: Message Navigator

Re: Position calculations on start/stop scintillators [message #18225 is a reply to message #18217]

Wed, 13 May 2015 14:56

miree
Messages: 71
Registered: June 2014

continuous participant

From: *ikp.physik.tu-darmstadt.de

Hi Tayfun,

I'll try to summarize some facts about the CircularMembrane first, and then try to outline of a Membrane selfcalibration algorithm:

The time and position calculation of the CircularMembraneScintillator processor needs to be calibrated in order to work. Especially the position determination depends strongly on the quality of the calibration.
The processor is not doing any calibration on it's own (like the DSSSD). It only provides some output that is useful to find good coefficients. All calibration procedures that I've seen so far need particle position information from other tracking detectors.

A minimization routine as described in my last post requires additional code: It needs to work with a given number (say 10000) of events. These events have to be analyzed over and over again, each time with slightly different calibration coefficients. The result of each single analysis schould be a quantity that allows to judge the quality of the calibration. Calculating this quantity involves an analysis similar to the current CircularMembraneScintillator. As minimization algorithm I would take a library such as the GNU scientific library. It contains the "simplex minimizer" which I would try first. It worked well in the case of Christian's DSSSD calibration.

I think it would be cool to have such an algorithm. But it will require some work to get it running, i.e. it is not a simple modification of the existing processor.

Report message to a moderator

[Message index]

		Position calculations on start/stop scintillators By: LScruton on Wed, 08 April 2015 18:24
		Re: Position calculations on start/stop scintillators By: miree on Thu, 09 April 2015 15:16
		Re: Position calculations on start/stop scintillators By: thuyuk on Thu, 07 May 2015 17:29
		Re: Position calculations on start/stop scintillators By: miree on Fri, 08 May 2015 11:23
		Re: Position calculations on start/stop scintillators By: miree on Mon, 11 May 2015 13:12
		Re: Position calculations on start/stop scintillators By: thuyuk on Tue, 12 May 2015 13:06
		Re: Position calculations on start/stop scintillators By: miree on Tue, 12 May 2015 15:24
		Re: Position calculations on start/stop scintillators By: thuyuk on Tue, 12 May 2015 15:39
		Re: Position calculations on start/stop scintillators By: miree on Tue, 12 May 2015 16:40
		Re: Position calculations on start/stop scintillators By: thuyuk on Wed, 13 May 2015 10:56
		Re: Position calculations on start/stop scintillators By: miree on Wed, 13 May 2015 14:56
		Re: Position calculations on start/stop scintillators By: thuyuk on Thu, 14 May 2015 12:07
		Re: Position calculations on start/stop scintillators By: miree on Fri, 15 May 2015 10:48
		Re: Position calculations on start/stop scintillators By: thuyuk on Tue, 19 May 2015 12:19
		Re: Position calculations on start/stop scintillators By: miree on Tue, 19 May 2015 14:29
		Re: Position calculations on start/stop scintillators By: miree on Wed, 20 May 2015 14:13
		Re: Position calculations on start/stop scintillators By: thuyuk on Thu, 21 May 2015 15:28

Previous Topic:	PRESPEC GEANT
Next Topic:	FRS Calibration Issue

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Wed Feb 18 01:03:43 CET 2026

Total time taken to generate the page: 0.00858 seconds