GSI Forum
GSI Helmholtzzentrum für Schwerionenforschung

Home » NUSTAR » NUSTAR PRESPEC » FRS - TPC Calibrations (Position Calibration Issues)
Re: FRS - TPC Calibrations [message #17023 is a reply to message #17020] Wed, 16 July 2014 13:06 Go to previous messageGo to previous message
mlcortes is currently offline  mlcortes
Messages: 41
Registered: July 2014
Location: Darmstadt
continuous participant
From: *ikp.physik.tu-darmstadt.de
Hi Scott,

I checked the 4 files and I see the masks for all of them.
Here is the assignment I am using for the TPC signals (this should be in the file Frs/tracking.config):


########################################################################
# TPC S21
########################################################################
processor Frs/TpcS21 FRS.StandardTpc
times[0:7] <- FrsTpcCrate.tdc0[16:23]
amplitudes[0:7] <- FrsTpcCrate.adc0[16:23]
fiber <- FrsTpcCrate.tdc1[23]
display x:y in TPCs/TpcS21
display x in TPCs/TpcS21
display y in TPCs/TpcS21
display x_fiber:y_fiber in TPCs/TpcS21
display checksums | gate_checksums in TPCs/TpcS21/checksums
end
########################################################################
# TPC S22
########################################################################
processor Frs/TpcS22 FRS.StandardTpc
times[0:7] <- FrsTpcCrate.tdc0[24:31]
amplitudes[0:7] <- FrsTpcCrate.adc0[24:31]
fiber <- FrsTpcCrate.tdc1[23]
display x:y in TPCs/TpcS22
display y in TPCs/TpcS22
display x in TPCs/TpcS22
display x_fiber:y_fiber in TPCs/TpcS22
display checksums | gate_checksums in TPCs/TpcS22/checksums
end

########################################################################
# TPC S41
########################################################################
processor Frs/TpcS41 FRS.StandardTpc
times[0:7] <- FrsTpcCrate.tdc1[0:7]
amplitudes[0:7] <- FrsTpcCrate.adc1[0:7]
fiber <- FrsTpcCrate.tdc1[25]
display x:y 1000,-50,50:800,-50,50 in TPCs/TpcS41
display y in TPCs/TpcS41
display x in TPCs/TpcS41
display x_fiber:y_fiber in TPCs/TpcS41
display checksums | gate_checksums in TPCs/TpcS41/checksums
end
########################################################################
# TPC S42
########################################################################
processor Frs/TpcS42 FRS.StandardTpc
times[0:7] <- FrsTpcCrate.tdc1[8:15]
amplitudes[0:7] <- FrsTpcCrate.adc1[8:15]
fiber <- FrsTpcCrate.tdc1[26]
display x:y 1000,-200,200:1000,-200,200 in TPCs/TpcS42
display y in TPCs/TpcS42
display x in TPCs/TpcS42
display x_fiber:y_fiber in TPCs/TpcS42
display checksums | gate_checksums in TPCs/TpcS42/checksums
end



------------------------------------

Then I look at the x:y histogram and I see the fibers. It may be good to leave smart histograms to start. If there is no good calibration you can be out of range and see nothing.
Is also to note that the input "fiber" in each processor is not really relevant as coincidences were made before passing the signals to the electronics (This may not be the case for all the experiments).
Also notice that at some point there was a problem with a TPC and not all the signals were used for the analysis. I think there is an elog entry about it. If i find it I let you know.
About the size of the grid, usually is the 12 x 6mm, nevertheless the logbook should say which fiber was used. Do you have a scan of the logbook?


Cheers,



Li^2
 
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Previous Topic: FRS-AGATA-LYCCA dead time
Next Topic: Scattering Angle Cut
Goto Forum:
  


Current Time: Sun Oct 06 00:40:27 CEST 2024

Total time taken to generate the page: 0.00774 seconds