GSI Forum: General » Problem with Root geometrys from CAD

Home » PANDA » PandaRoot » General » Problem with Root geometrys from CAD

Show: Today's Messages :: Polls :: Message Navigator

Re: Problem with Root geometrys from CAD [message #10908 is a reply to message #10633]

Fri, 06 August 2010 13:45

Christian Hammann
Messages: 24
Registered: July 2009
Location: Bonn

continuous participant

From: *cb.uni-bonn.de

Hi all

I have still have not been able to find a solution for this problem. However as it seems to be working with geant3 I have commited the code for the proto60 to svn, rev. 9625, along with a geometry for the proto60. At the moment only the crystals are included, no alveoles etc.

The geometry uses geometry version 18, mapperversion 10, module 7.

Regards

Christian

Christian Hammann
Universität Bonn
Helmholz-Institut für Strahlen und Kernphysik
Nußallee 14-16
53115 Bonn
Tel: +49 228 733895
Fax: +49 228 732505

Report message to a moderator

[Message index]

		Problem with Root geometrys from CAD By: Christian Hammann on Thu, 06 May 2010 11:14
		Re: Problem with Root geometrys from CAD By: Dima Melnychuk on Thu, 06 May 2010 14:43
		Re: Problem with Root geometrys from CAD By: Tobias Stockmanns on Thu, 06 May 2010 14:50
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Thu, 06 May 2010 15:24
		Re: Problem with Root geometrys from CAD By: Tobias Stockmanns on Fri, 07 May 2010 09:38
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Fri, 07 May 2010 10:56
		Re: Problem with Root geometrys from CAD By: Tobias Stockmanns on Fri, 07 May 2010 12:53
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Fri, 07 May 2010 13:10
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Fri, 07 May 2010 14:35
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Thu, 06 May 2010 15:21
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Mon, 17 May 2010 16:39
		Re: Problem with Root geometrys from CAD By: Dima Melnychuk on Mon, 17 May 2010 16:59
		Re: Problem with Root geometrys from CAD By: StefanoSpataro on Mon, 17 May 2010 17:25
		Re: Problem with Root geometrys from CAD By: Tobias Stockmanns on Tue, 18 May 2010 09:10
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Tue, 18 May 2010 11:27
		Re: Problem with Root geometrys from CAD By: Tobias Stockmanns on Tue, 18 May 2010 11:31
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Tue, 18 May 2010 16:47
		Re: Problem with Root geometrys from CAD By: Dima Melnychuk on Wed, 19 May 2010 15:28
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Wed, 19 May 2010 16:39
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Fri, 06 August 2010 13:45

Previous Topic:	Problem installing External package
Next Topic:	daily doxygen - genfit missing

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Wed Dec 04 01:25:18 CET 2024

Total time taken to generate the page: 0.00817 seconds