GSI Forum: General » Problem with Root geometrys from CAD

Home » PANDA » PandaRoot » General » Problem with Root geometrys from CAD

Show: Today's Messages :: Polls :: Message Navigator

Re: Problem with Root geometrys from CAD [message #10677 is a reply to message #10676]

Mon, 17 May 2010 16:59

Dima Melnychuk
Messages: 213
Registered: April 2004
Location: National Centre for Nucle...

first-grade participant

From: *fuw.edu.pl

Hi Christian,

I could reproduce your problem, at least huge amount of warnings with

*** Particle reached max step number (10000). ***

*********************************************************************************************************
* G4Track Information:   Particle = gamma,   Track ID = 88,   Parent ID = 81
*********************************************************************************************************

Step#    X(mm)    Y(mm)    Z(mm) KinE(MeV)  dE(MeV) StepLeng TrackLeng  NextVolume ProcName
10002    -11.6    -22.2      990     0.703        0        0      1.07 CrystalType6a Transportation
10003    -11.6    -22.2      990     0.703        0        0      1.07        cave Transportation
10004    -11.6    -22.2      990     0.703        0        0      1.07 CrystalType6a Transportation
10005    -11.6    -22.2      990     0.703        0        0      1.07        cave Transportation

And I have a suspicion what could case it but I could not check it so far due to technical difficulties. So I suspect that problem is due to the representation of crystal geometry with TGeoArb8 and I would guess that replacement with TGeoTrap could help. The conversion between two shapes is straightforward (you can find it in PndEmcStructure.cxx), however I understand why the CadConvertor provides TGeoArb8.

I tried to convert the geometry from the root file you provided, but simulation results in error which I do not understand. So in my opinion it would make sense to try to obtain the geometry with TGeoTrap directly from the CadConvertor, but at the moment I have no idea how.

My suspicion is based on the fact that such a warning appears also for the backward endcap geometry where TGeoArb8 are used and not for barrel geometry with TGeoTrap.

That's all I can say at the moment.

Best regards,

Dima

Report message to a moderator

[Message index]

		Problem with Root geometrys from CAD By: Christian Hammann on Thu, 06 May 2010 11:14
		Re: Problem with Root geometrys from CAD By: Dima Melnychuk on Thu, 06 May 2010 14:43
		Re: Problem with Root geometrys from CAD By: Tobias Stockmanns on Thu, 06 May 2010 14:50
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Thu, 06 May 2010 15:24
		Re: Problem with Root geometrys from CAD By: Tobias Stockmanns on Fri, 07 May 2010 09:38
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Fri, 07 May 2010 10:56
		Re: Problem with Root geometrys from CAD By: Tobias Stockmanns on Fri, 07 May 2010 12:53
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Fri, 07 May 2010 13:10
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Fri, 07 May 2010 14:35
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Thu, 06 May 2010 15:21
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Mon, 17 May 2010 16:39
		Re: Problem with Root geometrys from CAD By: Dima Melnychuk on Mon, 17 May 2010 16:59
		Re: Problem with Root geometrys from CAD By: StefanoSpataro on Mon, 17 May 2010 17:25
		Re: Problem with Root geometrys from CAD By: Tobias Stockmanns on Tue, 18 May 2010 09:10
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Tue, 18 May 2010 11:27
		Re: Problem with Root geometrys from CAD By: Tobias Stockmanns on Tue, 18 May 2010 11:31
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Tue, 18 May 2010 16:47
		Re: Problem with Root geometrys from CAD By: Dima Melnychuk on Wed, 19 May 2010 15:28
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Wed, 19 May 2010 16:39
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Fri, 06 August 2010 13:45

Previous Topic:	Problem installing External package
Next Topic:	daily doxygen - genfit missing

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Fri May 20 18:10:03 CEST 2022

Total time taken to generate the page: 0.00890 seconds