GSI Forum
GSI Helmholtzzentrum für Schwerionenforschung

Home » PANDA » PandaRoot » Monte Carlo Engines » Geant4: problem with set seed and cuts
Re: Geant4: problem with set seed and cuts [message #9535 is a reply to message #9516] Thu, 08 October 2009 10:54 Go to previous messageGo to previous message
Jerome Boucher is currently offline  Jerome Boucher
Messages: 11
Registered: October 2008
Location: IPNO
occasional visitor
From: *kph.uni-mainz.de
Hello!

I've tried the setSeeds method and it works Very Happy

I checked the g4Config.C , the option "stepLimiter+specialCuts+specialControls" is setted. If I looked to:-I- PndStack: the Total number of particles is changing according to my cut.

But if I look to the output it's always the same.


Index : 0     used in the geometry : Yes     recalculation needed : No 
 Material : air
 Range cuts        :  gamma 1 mm     e- 1 mm     e+ 1 mm 
 Energy thresholds :  gamma 990 eV     e- 990 eV     e+ 990 eV 
 Region(s) which use this couple : 
    DefaultRegionForTheWorld

Index : 1     used in the geometry : Yes     recalculation needed : No 
 Material : aluminium
 Range cuts        :  gamma 1 mm     e- 1 mm     e+ 1 mm 
 Energy thresholds :  gamma 6.88731 keV    e- 596.68 keV    e+ 568.011 keV
 Region(s) which use this couple : 
    DefaultRegionForTheWorld

Index : 2     used in the geometry : Yes     recalculation needed : No 
 Material : iron
 Range cuts        :  gamma 1 mm     e- 1 mm     e+ 1 mm 
 Energy thresholds :  gamma 20.8323 keV    e- 1.28002 MeV    e+ 1.21851 MeV
 Region(s) which use this couple : 
    DefaultRegionForTheWorld

Index : 3     used in the geometry : Yes     recalculation needed : No 
 Material : copper
 Range cuts        :  gamma 1 mm     e- 1 mm     e+ 1 mm 
 Energy thresholds :  gamma 24.6072 keV    e- 1.39521 MeV    e+ 1.31192 MeV
 Region(s) which use this couple : 
    DefaultRegionForTheWorld

Index : 4     used in the geometry : Yes     recalculation needed : No 
 Material : steel
 Range cuts        :  gamma 1 mm     e- 1 mm     e+ 1 mm 
 Energy thresholds :  gamma 20.8323 keV    e- 1.31192 MeV    e+ 1.23361 MeV
 Region(s) which use this couple : 
    DefaultRegionForTheWorld

Index : 5     used in the geometry : Yes     recalculation needed : No 
 Material : vacuum
 Range cuts        :  gamma 1 mm     e- 1 mm     e+ 1 mm 
 Energy thresholds :  gamma 990 eV     e- 990 eV     e+ 990 eV 
 Region(s) which use this couple : 
    DefaultRegionForTheWorld

Index : 6     used in the geometry : Yes     recalculation needed : No 
 Material : Al+Be
 Range cuts        :  gamma 1 mm     e- 1 mm     e+ 1 mm 
 Energy thresholds :  gamma 4.45676 keV    e- 496.074 keV    e+ 478.087 keV
 Region(s) which use this couple : 
    DefaultRegionForTheWorld

Index : 7     used in the geometry : Yes     recalculation needed : No 
 Material : TPCmixture
 Range cuts        :  gamma 1 mm     e- 1 mm     e+ 1 mm 
 Energy thresholds :  gamma 990 eV     e- 990 eV     e+ 990 eV 
 Region(s) which use this couple : 
    DefaultRegionForTheWorld

Index : 8     used in the geometry : Yes     recalculation needed : No 
 Material : silicon
 Range cuts        :  gamma 1 mm     e- 1 mm     e+ 1 mm 
 Energy thresholds :  gamma 6.88731 keV    e- 540.718 keV    e+ 521.113 keV
 Region(s) which use this couple : 
    DefaultRegionForTheWorld

Index : 9     used in the geometry : Yes     recalculation needed : No 
 Material : carbon
 Range cuts        :  gamma 1 mm     e- 1 mm     e+ 1 mm 
 Energy thresholds :  gamma 3.29462 keV    e- 568.011 keV    e+ 554.196 keV
 Region(s) which use this couple : 
    DefaultRegionForTheWorld

...



Could you explain me why?



best regards

jeorme
 
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Previous Topic: GEANT3: of energy loss and delta rays
Next Topic: elastic neutron scattering in Geant3
Goto Forum:
  


Current Time: Fri Apr 19 21:10:34 CEST 2024

Total time taken to generate the page: 0.01042 seconds