GSI Forum
GSI Helmholtzzentrum für Schwerionenforschung

Home » PANDA » PandaRoot » Analysis » [FIXED] why is total energyloss always too small?
[FIXED] why is total energyloss always too small? [message #15035] Mon, 29 July 2013 16:12 Go to next message
Prometeusz Jasinski is currently offline  Prometeusz Jasinski
Messages: 34
Registered: January 2012
continuous participant
From: *kph.uni-mainz.de
We tried to stop electrons in Silicon active material. The total energyloss calculated by the PandaSDS classes for the mctracks gives always about 300 keV to less, regardless if only one process happened or several.

Momentum [MeV] Eloss [MeV]
0.5 0.203
1 0.6119
2 1.553
3 2.532
4 3.521
5 4.515

Numbers are sharp, not distributed. What did I miss?

Neutrons are even not recognized.

The lower cut was already reduced in the corresponding macro.

[Updated on: Wed, 31 July 2013 08:18] by Moderator

Report message to a moderator

Re: why is total energyloss always too small? [message #15039 is a reply to message #15035] Tue, 30 July 2013 09:49 Go to previous messageGo to next message
StefanoSpataro is currently offline  StefanoSpataro
Messages: 2736
Registered: June 2005
Location: Torino
first-grade participant

From: 2.235.190*
Could you please attach the code you used? So that it is possible to check.
Have you compared Geant3 and Geant4, and also to disable the special cuts?
Re: why is total energyloss always too small? [message #15041 is a reply to message #15035] Tue, 30 July 2013 11:33 Go to previous messageGo to next message
Prometeusz Jasinski is currently offline  Prometeusz Jasinski
Messages: 34
Registered: January 2012
continuous participant
From: *kph.uni-mainz.de
Sure thing. So it is nothing obvious like momentum must not correspond to total energyloss, or so. I attached the code by my bachelor student.

As far as I remember Geant3 and Geant4 gave very similar results for protons. Electrons we did not test yet with Geant3.

How do I disable special cuts?

[Updated on: Tue, 30 July 2013 11:39]

Report message to a moderator

Re: why is total energyloss always too small? [message #15042 is a reply to message #15041] Tue, 30 July 2013 11:37 Go to previous messageGo to next message
Prometeusz Jasinski is currently offline  Prometeusz Jasinski
Messages: 34
Registered: January 2012
continuous participant
From: *kph.uni-mainz.de
And I just realized that he fills the histogram with "Eventeloss" for each eloss step and not each event. But at the end it is regardless, since we looked on the maximum bin entry only.
Re: why is total energyloss always too small? [message #15043 is a reply to message #15042] Tue, 30 July 2013 13:48 Go to previous messageGo to next message
Prometeusz Jasinski is currently offline  Prometeusz Jasinski
Messages: 34
Registered: January 2012
continuous participant
From: *kph.uni-mainz.de
Ok, found my own thought mistake:

m**2 = E**2 - p**2

=> Edep = E - E_mass_at_rest = sqrt(m**2+p**2)-m

with all the c's missing, so inserting masses and energies in MeV directly.

Gives the missing value in Edep. Nether thought about this before.

Thanks for your time

[Updated on: Tue, 30 July 2013 13:50]

Report message to a moderator

Re: why is total energyloss always too small? [message #15047 is a reply to message #15043] Tue, 30 July 2013 15:33 Go to previous messageGo to next message
StefanoSpataro is currently offline  StefanoSpataro
Messages: 2736
Registered: June 2005
Location: Torino
first-grade participant

From: 91.252.168*
Hi,
I suppose the problem is fixed now.
However, if you check gconfig/g3Config.c g4Config.C you can disable SpecialCuts. In the file SetCuts.C you can change the selections.in the past electrons where producing different results with g3 and g4.
Now it should be fixed.
Re: why is total energyloss always too small? [message #15060 is a reply to message #15047] Wed, 31 July 2013 08:16 Go to previous message
Prometeusz Jasinski is currently offline  Prometeusz Jasinski
Messages: 34
Registered: January 2012
continuous participant
From: *kph.uni-mainz.de
Yes, the mistake is found. Thank you for your efforts anyway.
Previous Topic: Updated Rho Tutorial
Next Topic: PndKinVtxFitter Resoultion
Goto Forum:
  


Current Time: Mon Nov 04 00:48:26 CET 2024

Total time taken to generate the page: 0.00613 seconds