GSI Forum
GSI Helmholtzzentrum für Schwerionenforschung

Home » PANDA » PandaRoot » Tracking » STTHit timestamps
STTHit timestamps [message #22483] Tue, 17 April 2018 11:28 Go to next message
JennyTaylor
Messages: 13
Registered: October 2016
occasional visitor
From: *physics.uu.se
I am working on a time clustering in the SttCellTrackFinder using Stt hits. For this I am using the STTHit time stamp and I am wondering what exactly the hit time stamp is, for example if it is the start or end of the signal. This information would be very helpful for the further development.

Best,
Jenny
Re: STTHit timestamps [message #22486 is a reply to message #22483] Tue, 17 April 2018 11:43 Go to previous messageGo to next message
Tobias Stockmanns is currently offline  Tobias Stockmanns
Messages: 489
Registered: May 2007
first-grade participant
From: *ikp.kfa-juelich.de
Dear Jenny,

in the event-based simulation the TimeStamp of the hit is set to -1. For the time-based simulation it is the sum of eventTime + flightTime + driftTime. So the time when the signal is registered in the electronics of the STT.

Cheers,

Tobias
Re: STTHit timestamps [message #22490 is a reply to message #22483] Tue, 17 April 2018 13:09 Go to previous messageGo to next message
Michael Papenbrock is currently offline  Michael Papenbrock
Messages: 24
Registered: September 2014
continuous participant
From: *physics.uu.se
If I'm not mistaken, this corresponds more or less to the leading edge of the signal. However, the trailing edge should be less affected by the actual flight path of the particle, since one will always have charges produced in the outer parts of the tubes when a particle enters and exits. Hence, that time information might be more useful for clustering. Will at all be possible to record either the time of the trailing edge or the time-over-threshold in the experiment?

Cheers,
Michael
Re: STTHit timestamps [message #22496 is a reply to message #22490] Tue, 17 April 2018 14:19 Go to previous messageGo to next message
Tobias Stockmanns is currently offline  Tobias Stockmanns
Messages: 489
Registered: May 2007
first-grade participant
From: *ikp.kfa-juelich.de
Hi Michael,

have a look at the presentation from Peter Wintz on the collaboration meeting in September https://indico.gsi.de/event/6361/contribution/0/material/slides/0.pdf.

There he used the trailing edge time to associate hits.

Cheers,

Tobias
Re: STTHit timestamps [message #22498 is a reply to message #22483] Tue, 17 April 2018 14:30 Go to previous messageGo to next message
Michael Papenbrock is currently offline  Michael Papenbrock
Messages: 24
Registered: September 2014
continuous participant
From: *physics.uu.se
Hi Tobias,

yes, that was actually the inspiration Smile
If I remember correctly, that was based on a test-setup and without PandaRoot, but I would hope that it will be in principle accessible also in the final experiment. However, I haven't seen an accessor to this kind of data in the PndSttHit class, and I'm not aware if this information is available at all at the reconstruction stage.
Do you know more about this or is something to be brought up to Peter?

Cheers,
Michael
Re: STTHit timestamps [message #22499 is a reply to message #22498] Tue, 17 April 2018 14:35 Go to previous message
Tobias Stockmanns is currently offline  Tobias Stockmanns
Messages: 489
Registered: May 2007
first-grade participant
From: *ikp.kfa-juelich.de
The STT is still lacking a proper digitization stage in PandaRoot and the output format of the STT electronics is not fixed. So, it is not clear if this information is available but if it proves to be usefull in simulations then it would be an argument to request it.

Cheers,

Tobias
Previous Topic: SDS digitization - new offset functionality
Next Topic: Genfit2 documentation
Goto Forum:
  


Current Time: Sat Dec 07 10:03:09 CET 2024

Total time taken to generate the page: 0.00778 seconds