GSI Forum: NUSTAR PRESPEC » LYCCA

Home » NUSTAR » NUSTAR PRESPEC » LYCCA - w-DSSSD Time Gated

Show: Today's Messages :: Polls :: Message Navigator

LYCCA - w-DSSSD Time Gated [message #17169]

Wed, 13 August 2014 12:48

thuyuk
Messages: 68
Registered: July 2014

continuous participant

From: *ific.uv.es

Hi all,

I would like to make use of LYCCA.DSSDTimeGated processor but I have some information missing: I couldn't locate the time signals of the p-side of the silicons in Crates.config. Would you be so kind to help me to update my config files?

Thank you very much in advance!

Tayfun

Report message to a moderator

Re: LYCCA - w-DSSSD Time Gated [message #17170 is a reply to message #17169]

Wed, 13 August 2014 14:01

miree
Messages: 71
Registered: June 2014

continuous participant

From: *ikp.physik.tu-darmstadt.de

Here is the layout of the Target and ToF crate as it was used in the 2014 campaign. I believe it was the same in 2012

crate  LyccaTargetTofCrate
    procid   90
    module   adc0    LYCCA.v785      # Target DSSSD p-side amplitudes
    module   adc1    LYCCA.v785      # Target DSSSD n-side amplitudes
    module   tdc     LYCCA.v775      # Target DSSSD times (I don't know if p- or n-side times)
    module   mhtdc0  LYCCA.v1290TMM  # ToF scintillators
    module   mhtdc1  LYCCA.v1290TMM  # ToF scintillators
    module   mhtdc2  LYCCA.v1290TMM  # ToF scintillators
end

Report message to a moderator

Re: LYCCA - w-DSSSD Time Gated [message #17171 is a reply to message #17170]

Wed, 13 August 2014 14:06

thuyuk
Messages: 68
Registered: July 2014

continuous participant

From: *ific.uv.es

Hi Michael,

Thank you very much for your reply.

I seems that I have the same layout. I'm a little bit confused: Do we have the time signals from one of the sides of the wall-DSSSD detectors?

Thank you!

Report message to a moderator

Re: LYCCA - w-DSSSD Time Gated [message #17172 is a reply to message #17171]

Wed, 13 August 2014 14:27

miree
Messages: 71
Registered: June 2014

continuous participant

From: *ikp.physik.tu-darmstadt.de

Hi,

yes... the TargetDSSSD times where not always present in the 2014 campaign Confused

. I don't remember if there were similar problems in 2012. It could be that this module didn't read the TargetDSSSD time signals.
Here are the WallDSSSD unpackers. The Wall DSSSD times are read by the CAENv767 multihit TDCs. They have 128 channels, which is enough for one side of all DSSSD modules in each crate. Again I'm not sure if p- or n-side times are read. As far as I remember, these were always present.

While analyzing commissioning data, I never used these time signals. Perhaps someone in the LYCCA collaboration has experience in how this information can be used.

crate LyccaWallCrate1
   procid    70
   module    adc01   LYCCA.v785
   module    adc02   LYCCA.v785
   module    adc05   LYCCA.v785
   module    adc06   LYCCA.v785
   module    adc07   LYCCA.v785
   module    adc08   LYCCA.v785
   module    adc11   LYCCA.v785
   module    adc12   LYCCA.v785
   module    mhtdc   LYCCA.v767
end

crate LyccaWallCrate2
    procid    80
    module    adc13   LYCCA.v785
    module    adc14   LYCCA.v785
    module    adc17   LYCCA.v785
    module    adc18   LYCCA.v785
    module    adc19   LYCCA.v785
    module    adc20   LYCCA.v785
    module    adc23   LYCCA.v785
    module    adc24   LYCCA.v785
    module    mhtdc   LYCCA.v767
end

Report message to a moderator

Re: LYCCA - w-DSSSD Time Gated [message #17173 is a reply to message #17172]

Wed, 13 August 2014 14:30

thuyuk
Messages: 68
Registered: July 2014

continuous participant

From: *ific.uv.es

All right! Thanks a lot for the crate entries for the time signals of w-DSSSD!

Cheers,

Report message to a moderator

Re: LYCCA - w-DSSSD Time Gated [message #17174 is a reply to message #17172]

Wed, 13 August 2014 14:33

Damian Ralet
Messages: 35
Registered: July 2014
Location: Darmstadt

continuous participant

From: *gsi.de

Hi Tayfun,

I did not look at it myself, but I know that Pico was looking at the timing of the target DSSD, and he was having time information for the Pb experiment.
He presented a few slides on his anlysis during the EGAN meeting this year.

Cheers,
Damian

Report message to a moderator

Re: LYCCA - w-DSSSD Time Gated [message #17175 is a reply to message #17174]

Wed, 13 August 2014 14:37

thuyuk
Messages: 68
Registered: July 2014

continuous participant

From: *ific.uv.es

Hi Damian,

Thanks a lot for the information.

I made use of the time of Target-DSSSD, but my intention was to make use of the Wall-DSSSD. We are suspecting possible pile-ups due to the high counting rate. We thought it might be useful to use a condition on time of the detector itself to suppress artificial effects. Maybe we are wrong but we would like to try it anyway Smile

Cheers

Report message to a moderator

Re: LYCCA - w-DSSSD Time Gated [message #17176 is a reply to message #17175]

Wed, 13 August 2014 15:24

mlcortes
Messages: 41
Registered: July 2014
Location: Darmstadt

continuous participant

From: *ikp.physik.tu-darmstadt.de

Hi Tayfun,

We looked at the times of the WallDssd for the Pb data of 2012. As Michael mentioned, the times of the wall (only the p-side) are read by Multihit modules. What we did, and seems to work quite fine, is to select the first hit of this modules and use it as the input for the Dssd processor. By doing this I can see nice time-energy spectra for all the modules. This selection (for my data) removes the need of a time-energy gate, so you can keep using the normal DSSD processor. I think there you can see if you need an aditional gate for your case
Actually we see a double time structure that seems to come from the diferent electronic chain of the modules 19,20,23 and 24. If you see the same, let us know! We are still not sure about the origin of it.
The code I am using goes like this:
Before the DSSD processors I select the hit

processor Lycca/WallDssdPreproc  UTILS.HitPick	
	  input_array[0:127]  <-  LyccaWallCrate1.tdc[0:127]
#	  display out_first
end
processor Lycca/WallDssdPreproc1  UTILS.HitPick	
	  input_array[0:127]  <-  LyccaWallCrate2.tdc[0:127]
#	  display out_first
end

And after that I put the time input if the DSDD processor. Here i copy just an example of the module 01 with all the inputs and visualization

processor Lycca/WallDssd01 LYCCA.DSSSD
	   #triggers 8 9 10
 	amplitude_p[0:15]  <-  LyccaWallCrate1.adc01[0:15]
	amplitude_n[0:15]  <-  LyccaWallCrate1.adc01[16:31]
	 time_p[0:15] <- Lycca/WallDssdPreproc.out_first[0:15]
	display time_p				   in WallDssd/Module01/time_p
    	display amplitude_p 2048,0,4096            in WallDssd/Module01/amplitude_p
   	display amplitude_n 2048,0,4096            in WallDssd/Module01/amplitude_n
    	display multiplicity_p 32,0,32             in WallDssd/Module01/multiplicity
    	display multiplicity_n 32,0,32             in WallDssd/Module01/multiplicity
	 display multiplicity_t 32,0,32 		   in WallDssd/Module01/multiplicity
	display multiplicity_p:multiplicity_t      in WallDssd/Module01/multiplicity 32,0,32: 32,0,32
	display cluster_multiplicity_p 32,0,32     in WallDssd/Module01/cluster_multiplicity
   	display cluster_multiplicity_n 32,0,32     in WallDssd/Module01/cluster_multiplicity
   	display cal_amplitude_p:cal_amplitude_n    in WallDssd/Module01
   	display amplitude_p:amplitude_n            in WallDssd/Module01
   	display dE                                 in WallDssd/Module01
  	display cal_time_p 			   in WallDssd/Module01/cal_times
	display cal_time_p:cal_amplitude_p 	   in WallDssd/Module01
	display time_p_sum:dE_p   500,0,10000:500,300,4000  in WallDssd/Module01
end

The last spectra should show you a nice energy time plot. Hope this is useful for you and let us know if you have any problem

Li^2

[Updated on: Wed, 13 August 2014 15:27]

Report message to a moderator

Re: LYCCA - w-DSSSD Time Gated [message #17179 is a reply to message #17176]

Wed, 13 August 2014 18:57

thuyuk
Messages: 68
Registered: July 2014

continuous participant

From: *ific.uv.es

Hi Liliana,

Many thanks for sharing the related part of the config file.

One question: In the DSSD module 12, the cable assignment doesn't follow the trend, e.g.:

	amplitude_p[0:13]  <-  LyccaWallCrate1.adc12[0:13]
	amplitude_p[15]  <-  LyccaWallCrate1.adc12[15]
	amplitude_n[0:15]  <-  LyccaWallCrate1.adc12[16:31]

do you know if the same applies for the time signals?

Thanks!
Tayfun

edit: Sorry! I just saw that only strip #14 is missing. I certainly can handle this! Please ignore this message.

[Updated on: Wed, 13 August 2014 18:58]

Report message to a moderator

Previous Topic:	problem with a processor (software-wise)
Next Topic:	Disagreement between the LISE++ calculations and the experiment

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Sun Nov 24 07:29:34 CET 2024

Total time taken to generate the page: 0.00698 seconds