GSI Forum: EMC » Geant3 tracking cuts for the EMC

Home » PANDA » PandaRoot » EMC » Geant3 tracking cuts for the EMC

Show: Today's Messages :: Polls :: Message Navigator

Re: Geant3 tracking cuts for the EMC [message #9578 is a reply to message #9571]

Mon, 19 October 2009 12:00

Christian Hammann
Messages: 24
Registered: July 2009
Location: Bonn

continuous participant

From: *cb.uni-bonn.de

Hi Soeren

Jens Soeren Lange wrote on Fri, 16 October 2009 17:36

I think experimentally (for "real data") it is really much easier to set threshold (e.g. discriminator) to energy (e.g. 1 MeV) and not to a particle range (e.g. 1 mm). In fact, so far we were (e.g. for the EMC) always talking about 1 MeV threshold or 3 MeV threshold or whatever value, but never about "threshold of 5 mm for a e-, but 3mm for a pi+ (in the same crystal)".

I think I have to agree with Bertram that the 1mm cut in geant 4 is more convienient for the EMC.
The energy cut in geant3 does not in any way correspond to the threshold which is set in the discriminator (in the case of the EMC). The cut applies to the individual particles in the shower, which are tracked or not depending on their energy. In the EMC only the sum of their energies is measured, no threshold can be set for individual shower particles. Thus this cut is more like a range cut, as with lower cut values more particles are propagated and more energy can be transported to the edge of the shower.

This can be seen in the example I gave above, by lowering the cut value the energy in the central crystal decreased by 30MeV!

The range cut in geant4 simply says you don't care whether the energy is deposited here or in 1mm distance. That's the case for the EMC: one doesn't care where in the crystal you have the energydeposition as long its in this crystal. That simply means the cut distance has to be much smaller than the size of the crystal (of course this has to be tuned).

Best regards
Christian

Christian Hammann
Universität Bonn
Helmholz-Institut für Strahlen und Kernphysik
Nußallee 14-16
53115 Bonn
Tel: +49 228 733895
Fax: +49 228 732505

Report message to a moderator

[Message index]

		Geant3 tracking cuts for the EMC By: Christian Hammann on Fri, 16 October 2009 13:58
		Re: Geant3 tracking cuts for the EMC By: Bertram Kopf on Fri, 16 October 2009 14:40
		Re: Geant3 tracking cuts for the EMC By: Bertram Kopf on Fri, 16 October 2009 15:06
		Re: Geant3 tracking cuts for the EMC By: Bertram Kopf on Fri, 16 October 2009 16:29
		Re: Geant3 tracking cuts for the EMC By: Christian Hammann on Mon, 19 October 2009 12:10
		Re: Geant3 tracking cuts for the EMC By: StefanoSpataro on Fri, 16 October 2009 15:10
		Re: Geant3 tracking cuts for the EMC By: Bertram Kopf on Fri, 16 October 2009 15:25
		Re: Geant3 tracking cuts for the EMC By: StefanoSpataro on Fri, 16 October 2009 15:30
		Re: Geant3 tracking cuts for the EMC By: Jens Sören Lange on Fri, 16 October 2009 17:36
		Re: Geant3 tracking cuts for the EMC By: Christian Hammann on Mon, 19 October 2009 12:00
		Re: Geant3 tracking cuts for the EMC By: Mohammad Al-Turany on Mon, 19 October 2009 15:29

Previous Topic:	Geometry of EMC Barrel Crystal
Next Topic:	Geometry converter for EMC crystals

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Sat May 09 18:20:32 CEST 2026

Total time taken to generate the page: 0.00820 seconds