GSI Forum
GSI Helmholtzzentrum für Schwerionenforschung

Home » PANDA » PandaRoot » General » Errors in SttHi
Errors in SttHi [message #14875] Wed, 19 June 2013 15:05 Go to next message
Tobias Stockmanns is currently offline  Tobias Stockmanns
Messages: 489
Registered: May 2007
first-grade participant
From: *ikp.kfa-juelich.de
Dear STT code developers,

I had a look into the hit errors stored in the STTHit.

The x,y,z coordinates given in the SttHit are the wire mid-position. The error given for them is 0.5 in x and y while in z it is 3 cm. In my opinion the error should be 1 / Sqrt(12) for x,y and tube length / Sqrt(12) for the z coordinate. Can you please check this?

When looking at the isochrones, these values are still given as a radius in cm with an error in cm. For the time-based simulations it is necessary to have a method to translate the stored time stamp (or time pulse) into a radius including error by giving the event time with error.

Cheers,

Tobias
Re: Errors in SttHi [message #14879 is a reply to message #14875] Wed, 19 June 2013 16:40 Go to previous messageGo to next message
Lia Lavezzi
Messages: 291
Registered: May 2007
Location: Torino
first-grade participant

From: *pv.infn.it
Dear Tobias,
Quote:

The x,y,z coordinates given in the SttHit are the wire mid-position. The error given for them is 0.5 in x and y while in z it is 3 cm. In my opinion the error should be 1 / Sqrt(12) for x,y and tube length / Sqrt(12) for the z coordinate. Can you please check this?

As you said, the x, y, z position coordinates of the STTHit are the coordinates of the center of the tube, so they will be known quite precisely. For this reason, I think that d/sqrt(12) is a too large error, since this must not be the error on the hit position, but the error on the tube position.
We actually kept the old values (0.5, 0.5, 3) since this info is not used anywhere in the code. When reconstructing tracks in the STT you always rely on the isochrone error.
Do you need these errors for some study?

Quote:

When looking at the isochrones, these values are still given as a radius in cm with an error in cm. For the time-based simulations it is necessary to have a method to translate the stored time stamp (or time pulse) into a radius including error by giving the event time with error.

You are right. We must create a STTDigi (the output of the single straw simulation), separate the STTHit from the STTDigi and put the function you mentioned between the two.

I will do that asap. Is that very urgent for your tests?
Cheers,
Lia.

Re: Errors in SttHi [message #14880 is a reply to message #14879] Wed, 19 June 2013 16:44 Go to previous messageGo to next message
Tobias Stockmanns is currently offline  Tobias Stockmanns
Messages: 489
Registered: May 2007
first-grade participant
From: *ikp.kfa-juelich.de
Dear Lia,

the x,y values of the STTHits are used for fast track finding by Marius and I use them for a Riemann-based track finder including the STT. This is the reason why I have asked for the change in the errors.

The other point is not so urgent because I am busy at the moment with other stuff. I just figured out the problem when I was looking into the code.

Cheers,

Tobias
Re: Errors in SttHi [message #14881 is a reply to message #14880] Wed, 19 June 2013 17:03 Go to previous message
Lia Lavezzi
Messages: 291
Registered: May 2007
Location: Torino
first-grade participant

From: *pv.infn.it
Dear Tobias,
if you just use the xyz coordinates and not the errors then it should not be a big deal. I think I could put the errors to 0 0 0 just to make it clear that they must not be used now.

Concerning the isochrone/time issue, thank you for pointing that out. This is something we have to do since a while, but now we are quite busy with track finding stuff...

Cheers,
Lia.
Previous Topic: About run time of new reco macro
Next Topic: Constant magnetic field instead Solenoid Field maps
Goto Forum:
  


Current Time: Sun Aug 25 13:25:54 CEST 2024

Total time taken to generate the page: 0.00816 seconds