GSI Forum: General » Problem with Root geometrys from CAD

Home » PANDA » PandaRoot » General » Problem with Root geometrys from CAD

Show: Today's Messages :: Polls :: Message Navigator

Re: Problem with Root geometrys from CAD [message #10702 is a reply to message #10633]

Wed, 19 May 2010 15:28

Dima Melnychuk
Messages: 213
Registered: April 2004
Location: National Centre for Nucle...

first-grade participant

From: *fuw.edu.pl

Hi Christian,

I have just observed that with changing geometry navigation in /gconfig/g4Config.C from "geomRoot" to "geomRootToGeant4", i.e. from ROOT navigation to native Geant4 navigation the warning

*** Particle reached max step number (10000). ***

disappeared with simulation with single_cad_crystal2_emc_proto60.root geometry.

I do not know it it is a solution and how it affects the other two problems you reported, but at least it's some progress.

Best regards,

Dima

Report message to a moderator

[Message index]

		Problem with Root geometrys from CAD By: Christian Hammann on Thu, 06 May 2010 11:14
		Re: Problem with Root geometrys from CAD By: Dima Melnychuk on Thu, 06 May 2010 14:43
		Re: Problem with Root geometrys from CAD By: Tobias Stockmanns on Thu, 06 May 2010 14:50
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Thu, 06 May 2010 15:24
		Re: Problem with Root geometrys from CAD By: Tobias Stockmanns on Fri, 07 May 2010 09:38
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Fri, 07 May 2010 10:56
		Re: Problem with Root geometrys from CAD By: Tobias Stockmanns on Fri, 07 May 2010 12:53
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Fri, 07 May 2010 13:10
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Fri, 07 May 2010 14:35
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Thu, 06 May 2010 15:21
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Mon, 17 May 2010 16:39
		Re: Problem with Root geometrys from CAD By: Dima Melnychuk on Mon, 17 May 2010 16:59
		Re: Problem with Root geometrys from CAD By: StefanoSpataro on Mon, 17 May 2010 17:25
		Re: Problem with Root geometrys from CAD By: Tobias Stockmanns on Tue, 18 May 2010 09:10
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Tue, 18 May 2010 11:27
		Re: Problem with Root geometrys from CAD By: Tobias Stockmanns on Tue, 18 May 2010 11:31
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Tue, 18 May 2010 16:47
		Re: Problem with Root geometrys from CAD By: Dima Melnychuk on Wed, 19 May 2010 15:28
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Wed, 19 May 2010 16:39
		Re: Problem with Root geometrys from CAD By: Christian Hammann on Fri, 06 August 2010 13:45

Previous Topic:	Problem installing External package
Next Topic:	daily doxygen - genfit missing

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Sun May 11 04:41:03 CEST 2025

Total time taken to generate the page: 0.01007 seconds